Lecture - 2 (impact of jets)

Before starting with impact of jets we must learn about forces. Force is nothing but rate of change in linear momentum. When we apply force on a body, than its Momentum will change and this change in momentum will represented by subtraction of initial momentum of body from its final momentum.
Force applied on a body = final momentum of body - initial momentum of body
Let us consider a stationary vertical plate on which a jet is striking. The jet is having diameter 'd'. The mass flow rate of Jet is represented by 'm' kg/s. This simply means that 'm' kilogram of water is coming out of nozzle per second. The jet is striking at the middle of the plate with velocity 'V1' metre per second. After the impact of Jet on the plate, the jet will split equally and flows over the plate. After that the jet will exit the plate from its tip in tangential direction. Now here Jet is striking the plate normally or perpendicularly at point 1 and exit the plate tangentially from the tip of the vertical plate represented by point 2 with velocity 'V2' m/s. If we consider this plate to be frictionless then the entry velocity and exit velocity will be same (V1=V2).

In above figure consider this plate vertical and jet is striking perpendicularly to the plate.
Water jet striking with the force 'Fj ' on stationary plate. Now plate will apply reaction force 'Fp '. This jet force and plate force are equal and opposite action and reaction forces.
Fp = rate of change in linear momentum
     = Final momentum - initial momentum
As we know Fj = -Fp 
∴ Fj = initial momentum - final momentum
       = mV1 - mV2


After this continue to lecture - 3

you guys can check its video explaination also on my you tube channel Mechanical education hub

Comments

Post a Comment

Popular posts from this blog

Lecture - 11 (Transmission angle in four bar mechanism)

Image
The angle between coupler link and output link in four bar mechanism is known as transmission angle. It is represented as ' μ'.   In the given figure Let us consider angle between link AO and link OC (fixed link) is represented by ' θ'.   Let us consider length of link OC is 'a', length of link OA is 'b', length of AB is 'c' and length of BC is 'd'.  According to law of cosine we get -  Now  μ will be different for different values of  θ. μ will be maximum for  θ = 180 degrees  & minimum for  θ = 0 degrees.   Problem 1-  Calculate maximum and minimum value of transmission angle for the following mechanism. Length of link OC is 5cm, length of link AO is 1cm, length of link AB is 4cm and length of link BC is 3cm. Solution 1 -   To calculate minimum value of transmission angle observe the mechanism when  θ = 0 degrees   To calculate maximum value of transmission angle observe the mechani...
Read more

Lecture - 8 ( problems on degrees of freedom)

Image
PROBLEM 1  - For the mechanism shown in figure, calculate it's degrees of freedom (F) SOLUTION 1  -  number of links (L) = 8 Number of binary joints (J) = 10 Number of higher pair (H) = 0 Number of those motions which are not the part of mechanism (N) = 0 KUTZBACH equation: F=3(L-1) - 2(J) - H - N F = 3(8-1) - 2(10) - 0 - 0 = 1 F = 1  PROBLEM 2 -  Calculate degrees of freedom for given mechanism SOLUTION 2 -   L = 4 ; J = 3 ; H = 1 ; N = 1 F = 3(L-1) - 2J - H - N = 3(4-1) -2(3) -1 -1 = 1 F = 1    PROBLEM 3 -  Calculate degrees of freedom for given mechanism.  SOLUTION 3 -   L = 5 ; H = 1 ; J = 5 ; N = 0 F = 3(5-1) -2(5) - 1 - 0 = 1  F = 1 PROBLEM 4 -  Calculate degrees of freedom for given mechanism SOLUTION 4 -    Here one link is spring. Spring is the link of flexible length. Spring can be replaced by 2 links connected with turning pair. ...
Read more

Lecture - 15 (Mechanical advantage, mechanism efficiency, toggle mechanism)

Image
Mechanical advantage   It is defined as the ratio of the force produced by a machine to the force applied to it, used in assessing the performance of machine.  The combination of pulley system is shown in the below figure-  Here for lifting download F force is required but the effort given to the system is 8 times less, which is the good example of mechanical advantage. For the above system mechanical advantage is 8 Mechanical advantage = load / effort  Mechanical advantage for linear motion is -  Mechanical advantage for angular motion is -  Efficiency of system or mechanism Efficiency of the system is defined as the ratio of output power to the input power. PROBLEM - Find out mechanical advantage of the given mechanism having 100% efficiency. Solution -  In the sense of angular velocity It means that above mechanism is toogle mechanism.  Toggle mechanism   Those mechanism whose mechan...
Read more